拉伸強度Tensile Strength

JIS K7161-1:2014 Plastics - Determination of tensile properties - Part 1: General principles塑料拉伸性能的測定第1部分：總則

JIS K7161-2:2014 (取代JIS K 7113:1995) Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

ISO 6259-3:2015 (聚烯烴管材) Thermoplastics Pipes - Determination of Tensile Properties - Part 3: Polyolefin Pipes熱塑性塑料管拉伸性能的測定第3部分：聚烯烴管

GB/T 8804.3-2003 (聚烯烴管材) Thermoplastics Pipes - Determination of Tensile Properties - Part 3: Polyolefin Pipes熱塑性塑料管拉伸性能的測定第1部分：聚烯烴管

GB/T 8804.2-2003 (PVC-U, PVC-C, PVC-HI管材) Thermoplastic pipes--Determination of tensile properties--Part 2: Pipes made of unplasticized poly(vinyl chloride)(PVC-U),chlorinated poly(vinyl chloride)(PVC-C)and high-impact poly(vinyl chloride)(PVC-HI) 熱塑性塑料管材 拉伸性能測定 第2部分;硬聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)和高抗沖聚氯乙烯(PVC-HI)管材

JIS C3005:2014 (電線電纜絕緣與護套) Test methods for rubber or plastic insulated wires and cables橡膠或塑料絕緣電線和電纜的試驗方法

ASTM D638-14 Standard Test Method for Tensile Properties of Plastics塑料拉伸性能的標準試驗方法

ASTM D1784-11 Section11.3 (PVC/CPVC)Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds 硬質聚氯乙烯(PVC)化合物和氯化聚氯乙烯(CPVC)化合物的標準規范

ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

GB/T 1040.2-2006 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics拉伸性能的測定　第2部分：模塑和擠塑塑料的試驗條件

斷裂伸長率Elongation at break

JIS C3005:2014 (電線電纜絕緣與護套) Test methods for rubber or plastic insulated wires and cables橡膠或塑料絕緣電線和電纜的試驗方法

ASTM D638-14 Standard Test Method for Tensile Properties of Plastics塑料拉伸性能的標準試驗方法

ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

GB/T 1040.2-2006 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

JIS K7161-1:2014 Plastics - Determination of tensile properties - Part 1: General principles塑料拉伸性能的測定第1部分：總則

JIS K7161-2:2014 (取代JIS K 7113:1995) Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

ISO 6259-3:2015 (聚烯烴管材) Thermoplastics Pipes - Determination of Tensile Properties - Part 3: Polyolefin Pipes熱塑性塑料管拉伸性能的測定第3部分：聚烯烴管

GB/T 8804.3-2003 (聚烯烴管材) Thermoplastics Pipes - Determination of Tensile Properties - Part 3: Polyolefin Pipes熱塑性塑料管拉伸性能的測定第3部分：聚烯烴管

GB/T 8804.2-2003 (PVC-U, PVC-C, PVC-HI管材) Thermoplastic pipes--Determination of tensile properties--Part 2: Pipes made of unplasticized poly(vinyl chloride)(PVC-U),chlorinated poly(vinyl chloride)(PVC-C)and high-impact poly(vinyl chloride)(PVC-HI) 熱塑性塑料管材-拉伸性能測定-第2部分：硬聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)和高抗沖

拉伸模量Tensile Modulus

ASTM D638-14 Standard Test Method for Tensile Properties of Plastics塑料拉伸性能的標準試驗方法

ASTM D1784-11 Section11.3 (PVC/CPVC)Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds硬質聚氯乙烯(PVC)化合物和氯化聚氯乙烯(CPVC)化合物的標準規范

IDT ASTM D638-14 Standard Test Method for Tensile Properties of Plastics塑料拉伸性能的標準試驗方法

ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

GB/T 1040.2-2006 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

泊松比Poisson ratio

ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

GB/T 1040.2-2006 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics塑料拉伸性能的測定第2部分：模塑和擠壓塑料的試驗條件

ASTM D638-14 Standard Test Method for Tensile Properties of Plastics塑料拉伸性能的標準試驗方法

ASTM D3039/D3039M-17 Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials聚合物基復合材料拉伸性能的標準試驗方法

彎曲強度Flexural Strength

ASTM D790-17 Method A、B Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials未增強和增強塑料及電絕緣材料彎曲性能的標準試驗方法

ASTM D229-19e1 Section 12~24 (電絕緣用的硬板材)Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation電絕緣用剛性薄板和板材的標準試驗方法

IDT ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials未增強和增強塑料及電絕緣材料彎曲性能的標準試驗方法

ISO 178:2019 Method A、B Plastics — Determination of flexural properties塑料.彎曲性能的測定

GB/T 9341-2008 Plastics — Determination of flexural properties塑料.彎曲性能的測定

DIN EN ISO 178:2019 (取代DIN 53452:1977)Plastics — Determination of flexural properties塑料.彎曲性能的測定

彎曲模量Flexural modulus

ASTM D790-17 Method A Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials未增強和增強塑料及電絕緣材料彎曲性能的標準試驗方法

ASTM D229-19e1 Section 12~24 (電絕緣用的硬板材) Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation電絕緣用剛性薄板和板材的標準試驗方法

IDT ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials未增強和增強塑料及電絕緣材料彎曲性能的標準試驗方法

ISO 178:2019 Method A、B Plastics — Determination of flexural properties塑料.彎曲性能的測定

GB/T 9341-2008 Plastics — Determination of flexural properties塑料.彎曲性能的測定

邵氏A型硬度Shore Hardness Type A

ASTM D2240-15 Standard Test Method for Rubber Property-Durometer Hardness 橡膠性能的標準試驗方法-硬度計的硬度

BS EN ISO 868:2003 (取代BS 2782-3:1981 365B ) Plastics and ebonite-Determination of indentation hardness by means of a durometer (Shore hardness) 塑料和硬質橡膠-用硬度計測定壓痕硬度(邵氏硬度)

ISO 868:2003 Plastics and Ebonite-Determination of Indentation Hardness by Means of a Durometer (Shore Hardness) 塑料和硬質橡膠-用硬度計測定壓痕硬度(邵氏硬度)

GB/T 2411-2008 Plastics and Ebonite-Determination of Indentation Hardness by Means of a Durometer (Shore Hardness) 塑料和硬質橡膠-用硬度計測定壓痕硬度(邵氏硬度)

邵氏OO型硬度Shore Hardness Type OO

ASTM D2240-15 Standard Test Method for Rubber Property-Durometer Hardness 橡膠性能的標準試驗方法-硬度計的硬度

邵氏D型硬度Shore Hardness Type D

ASTM D2240-15 Standard Test Method for Rubber Property-Durometer Hardness 橡膠性能的標準試驗方法-硬度計的硬度

BS EN ISO 868:2003 (取代BS 2782-3:1981 365B ) Plastics and ebonite-Determination of indentation hardness by means of a durometer (Shore hardness) 塑料和硬質橡膠-用硬度計測定壓痕硬度(邵氏硬度)

ISO 868:2003 Plastics and Ebonite-Determination of Indentation Hardness by Means of a Durometer (Shore Hardness) 塑料和硬質橡膠-用硬度計測定壓痕硬度(邵氏硬度)

GB/T 2411-2008 Plastics and Ebonite-Determination of Indentation Hardness by Means of a Durometer (Shore Hardness) 塑料和硬質橡膠-用硬度計測定壓痕硬度(邵氏硬度)

洛氏硬度Rockwell Hardness

ASTM D785-08 (2015) Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials 塑料和電絕緣材料洛氏硬度的標準試驗方法

ISO 2039-2:1987 Plastics-Determination of Hardness-Part 2: Rockwell Hardness 塑料-硬度的測定-第2部分：洛氏硬度

JIS K7202-2:2001 Plastics-Determination of Hardness-Part 2: Rockwell Hardness 塑料-硬度的測定-第2部分：洛氏硬度

GB/T 3398.2-2008 Plastics-Determination of Hardness-Part 2: Rockwell Hardness 塑料-硬度的測定-第2部分：洛氏硬度

巴氏硬度Barcol Hardness

ASTM D2583-13a Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor 用Barcol壓縮器測定硬質塑料壓痕硬度的標準試驗方法

EN 59:2016 Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester 玻璃增強塑料.用巴氏硬度計測定壓痕硬度

GB/T 3854-2017 Test method for hardness of reinforced plastics by means of a Barcol impresser增強塑料巴柯?tīng)栍捕仍囼灧椒?/p>

球壓痕硬度Ball indentation hardness

ISO 2039-1:2001 Plastics - Determination of Hardness - Part 1: Ball Indentation Method

GB/T 3398.1-2008 塑料.硬度的測定.第1部分：球形壓痕法

DIN EN ISO 2039-1: 2003 (取代DIN 53456:1973 )Plastics - Determination of hardness - Part 1: Ball indentation method (ISO 2039-1:2001) 塑料硬度的測定第1部分：球形壓痕法

懸臂梁沖擊強度IZOD Impact Strength

ASTM D1784-11 Section11.4 (PVC/CPVC)Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds硬質聚氯乙烯(PVC)化合物和氯化聚氯乙烯(CPVC)化合物的標準規范

ASTM D4812-19 Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics 塑料無缺口懸臂梁抗沖擊性的標準試驗方法

ISO 180:2019 Plastics - Determination of Izod impact strength塑料.伊佐德沖擊強度的測定

GB/T 1843-2008 Plastics - Determination of Izod impact strength塑料.伊佐德沖擊強度的測定

ASTM D256-10(2018) (有缺口) Method A、C、E Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics 測定塑料的伊佐德擺錘抗沖擊性的標準試驗方法

ASTM D229-19e1 Section 26 (電絕緣用的硬板材) Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation電絕緣用剛性薄板和板材的標準試驗方法

JIS K7110:1999 Plastics - Determination of Izod impact strength塑料.伊佐德沖擊強度的測定

簡支梁沖擊強度CHARPY Impact Strength

GB/T 1451-2005 (玻璃纖維增強塑料) 纖維增強塑料簡支梁式?jīng)_擊韌性試驗方法

ISO 179-2:1997/Cor.1:1998+Amd.1:2011 Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test 塑料.簡支梁沖擊性能的測定.第2部分：儀器沖擊試驗

ASTM D6110-18 (有缺口) Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 測定塑料缺口試樣抗簡支梁沖擊性的標準試驗方法

ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test塑料簡支梁沖擊性能的測定第1部分：非儀器沖擊試驗

GB/T 1043.1-2008 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test塑料簡支梁沖擊性能的測定第1部分：非儀器沖擊試驗

小試樣沖擊強度Impact test on dynstat Impact Strength， 小試樣彎曲強度Bending test on dynstat test specimens

DIN 53435:2018 Testing of plastics - Bending test and impact test on dynstat test specimens塑料試驗 小樣試樣的彎曲試驗和沖擊試驗

低溫環境中的懸臂梁和簡支梁沖擊強度IZOD and CHARPY Impact Strength in Low temperature Environment

GB/T 1451-2005 (玻璃纖維增強塑料) 纖維增強塑料簡支梁式?jīng)_擊韌性試驗方法

ISO 179-2:1997/Cor.1:1998+Amd.1:2011 Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test 塑料.簡支梁沖擊性能的測定.第2部分：儀器沖擊試驗

ASTM D6110-18 (有缺口) Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics 測定塑料缺口試樣抗簡支梁沖擊性的標準試驗方法

ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test塑料簡支梁沖擊性能的測定第1部分：非儀器沖擊試驗

GB/T 1043.1-2008 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test塑料簡支梁沖擊性能的測定第1部分：非儀器沖擊試驗

壓縮強度Compressive Strength

ASTM D348-13 Section 14-17 (電絕緣用剛性管) Standard Test Methods for Rigid Tubes Used for Electrical Insulation電絕緣用剛性管的標準試驗方法

ASTM D695-15 Standard Test Method for Compressive Properties of Rigid Plastics硬質塑料壓縮性能的標準試驗方法

ISO 604:2002 Plastics - Determination of Compressive Properties塑料.壓縮性能的測定

GB/T 1041-2008 Plastics - Determination of Compressive Properties塑料.壓縮性能的測定

壓縮模量 Compressive Modulus

ASTM D695-15 Standard Test Method for Compressive Properties of Rigid Plastics硬質塑料壓縮性能的標準試驗方法

ISO 604:2002 Plastics - Determination of Compressive Properties塑料.壓縮性能的測定

GB/T 1041-2008 Plastics - Determination of Compressive Properties塑料.壓縮性能的測定

落錘沖擊強度Falling Weight Impact Strength

ASTM D5420-16 (硬質塑料) Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)用落錘沖擊的撞針測定平面剛性塑料試樣抗沖擊性的標準試驗方法(加德納沖擊)

ASTM D4226-16 (PVC建材) Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products硬質聚氯乙烯(PVC)建筑產品抗沖擊性的標準試驗方法

多軸沖擊Multiaxial Impact

ISO 6603-2:2000 Plastics - Determination of Puncture Impact Behaviour of Rigid Plastics - Part 2: Instrumented Impact Testing塑料.硬質塑料穿刺沖擊性能的測定.第2部分：儀器沖擊試驗

ASTM D3763-18 Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors用載荷和位移傳感器測定塑料高速穿刺性能的標準試驗方法

拉伸蠕變Tensile Creep

ISO 899-1-2017 Plastics - Determination of creep behaviour - Part 1: Tensile creep塑料.蠕變性能的測定.第1部分：拉伸蠕變

GB/T 11546.1-2008 Plastics - Determination of creep behaviour - Part 1: Tensile creep塑料.蠕變性能的測定.第1部分：拉伸蠕變

拉伸斷裂伸長率保留率Retention rate of elongation at break

GB 20197-2006 降解塑料的定義、分類、標識和降解性能要求

磨耗性能(Taber)Taber Abrasion Resistance

ASTM D1044-19 Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion by the Taber Abraser用泰伯研磨機測定透明塑料表面耐磨性的標準試驗方法

ASTM G195-18 Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser使用旋轉平臺研磨機進行磨損試驗的標準指南

ANSI/SAE Z26.1-1996第5.17節 Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways - Safety Standard在陸地公路上運行的機動車輛和機動車輛設備用安全玻璃材料.安全標準

ISO 9352:2012 Plastics - Determination of resistance to wear by abrasive wheels 塑料.用砂輪測定耐磨性

GB/T 5478-2008 Plastics - Determination of resistance to wear by abrasive wheels 塑料.用砂輪測定耐磨性

線纜刮磨Scrape abrasion

ISO 6722:2006/Cor.1:2012第9.3節 Road Vehicles - 60 V and 600 V Single-Core Cables - Dimensions, Test Methods and Requirements道路車輛.60V和600V單芯電纜.尺寸，試驗方法和要求

GB/T 25085-2010第9.3節 Road Vehicles - 60 V and 600 V Single-Core Cables - Dimensions, Test Methods and Requirements道路車輛.60V和600V單芯電纜.尺寸，試驗方法和要求

線纜拖磨Sandpaper abrasion

ISO 6722:2006/Cor.1:2012第9.2節Road Vehicles - 60 V and 600 V Single-Core Cables - Dimensions, Test Methods and Requirements道路車輛.60V和600V單芯電纜.尺寸，試驗方法和要求

GB/T 25085-2010第9.2節Road Vehicles - 60 V and 600 V Single-Core Cables - Dimensions, Test Methods and Requirements道路車輛.60V和600V單芯電纜.尺寸，試驗方法和要求

承載強度Bearing strength

ASTM D953-18 程序A、程序C(硬質塑料) Standard Test Method for Pin-Bearing Strength of Plastics塑料銷軸承強度的標準試驗方法

穿孔剪切強度Shear Strength by Punch

ASTM D732-17 Standard Test Method for Shear Strength of Plastics by Punch Tool用沖孔工具測定塑料剪切強度的標準試驗方法

HG/T 3839-2006 (2017) Standard Test Method for Shear Strength of Plastics by Punch Tool用沖孔工具測定塑料剪切強度的標準試驗方法

密度Density

JIS K7112:1999 Method A Plastics - Methods of Determining the Density and Relative Density of Non-Cellular Plastics塑料.非泡沫塑料密度和相對密度的測定方法

BS EN ISO 1183-1:2019 Method A(取代BS 2782-6:1991)(取代BS 2782-6:1991 Methods 620A-620D ) Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method塑料.非泡沫塑料密度的測定方法.第1部分：浸漬法，液體比重瓶法和滴定法

ASTM D792-13 (Immersion Method)Method A、B Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement用位移法測定塑料密度和比重(相對密度)的標準試驗方法

ISO 1183-1:2019 Method A (Immersion Method) Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method塑料.非泡沫塑料密度的測定方法.第1部分：浸漬法，液體比重瓶法和滴定法

DIN EN ISO 1183-1:2013 Method A(浸泡法)(取代DIN 53479:1976) Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method塑料.非泡沫塑料密度的測定方法.第1部分：浸漬法，液體比重瓶法和滴定法

ASTM D348-13 Section 20-27 (電絕緣材料用硬管) Standard Test Methods for Rigid Tubes Used for Electrical Insulation電絕緣用剛性管的標準試驗方法

ISO 1183-1:2019 method B Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method塑料.非泡沫塑料密度的測定方法.第1部分：浸漬法，液體比重瓶法和滴定法

GB/T 1033.1-2008方法B Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method塑料.非泡沫塑料密度的測定方法.第1部分：浸漬法，液體比重瓶法和滴定法

表觀密度Apparent Density

GB/T 1636-2008 (塑料粉末或粒料)Plastics - Determination of Apparent Density of Material That Can Be Poured from a Specified Funnel塑料.可從指定漏斗傾倒的材料表觀密度的測定

BS EN ISO 60:2000 (塑料粉末或粒料)Plastics - Determination of Apparent Density of Material That Can Be Poured from a Specified Funnel塑料.可從指定漏斗傾倒的材料表觀密度的測定

GB/T 11409-2008 第3.6節 Test method rubber antiagers and vulcanizing accelerators 橡膠防老劑、硫化促進劑試驗方法 標準

熔融指數Melt index(MI)

ISO 1133-1:2011 Procedure A、B Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics塑料.熱塑性塑料熔體質量流率(MFR)和熔體體積流率(MVR)的測定

GB/T 3682-1-2018 Method A、B Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics塑料.熱塑性塑料熔體質量流率(MFR)和熔體體積流率(MVR)的測定

JIS K7210:1999 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics塑料.熱塑性塑料熔體質量流率(MFR)和熔體體積流率(MVR)的測定

ASTM D1238-20 Procedure A,B,C Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer用擠壓塑性計測定熱塑性塑料熔體流動速率的標準試驗方法

流動速率比Flow rate ratio

ISO 1133-1:2019 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics塑料.熱塑性塑料熔體質量流率(MFR)和熔體體積流率(MVR)的測定

GB/T 3682.1-2018 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics塑料.熱塑性塑料熔體質量流率(MFR)和熔體體積流率(MVR)的測定

ASTM D1238-13 Procedure D Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer用擠壓塑性計測定熱塑性塑料熔體流動速率的標準試驗方法

熱變形溫度Heat deflection temperature(HDT)

ASTM D648-18 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position在邊緣位置彎曲載荷下塑料撓曲溫度的標準試驗方法

ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite塑料.負載下?lián)锨鷾囟鹊臏y定.第2部分：塑料和硬橡膠

GB/T 8802-2001 (塑料管材、管件) Thermoplastics Pipes and Fittings - Determination of Vicat Softening Temperature熱塑性塑料管材、管件維卡軟化溫度的測定

ISO 2507.1:1995 Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 1: General Test Method熱塑性塑料管和配件維卡軟化溫度第1部分：通用試驗方法

ISO 2507.2:1995 (塑料管材、管件) Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 2: Test Conditions for Unplasticized Poly(Vinyl Chloride) (PVC-U) or Chlorinated Poly(Vinyl Chloride) (PVC-C) Pipes and Fittings and for High Impact Resistance Poly(Vinyl Chloride) (PVC-HI) Pipes熱塑性塑料管和配件維卡軟化溫度第2部分：未增塑聚氯乙烯(PVC-U)或氯化聚氯乙烯(PVC-C)管和配件及高抗沖擊聚氯乙烯(PVC-HI)管的試驗條件

BS EN ISO 8442-1:1998(2005) Section 6.5 (餐廚用刀具、容器) Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 1: Requirements for Cutlery for the Preparation of Food與食品接觸的材料和物品.餐具和凹形餐具.第1部分：食品制備用餐具的要求

GB/T 1634.2-2019 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite塑料.負載下?lián)锨鷾囟鹊臏y定.第2部分：塑料和硬橡膠

ASTM D1784-20 Section11.5 (PVC/CPVC)Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds硬質聚氯乙烯(PVC)化合物和氯化聚氯乙烯(CPVC)化合物規范的標準分類系統和基礎

維卡軟化點Vicat softening temperature(VST)

ASTM D1525-17 Standard Test Method for Vicat Softening Temperature of Plastics塑料維卡軟化溫度的標準試驗方法

ISO 306:2013 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)塑料.熱塑性材料.維卡軟化溫度(VST)的測定

GB/T 1633-2000 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST)塑料.熱塑性材料.維卡軟化溫度(VST)的測定

IEC 60065:2014/Cor.2:2016 Table 3 note f Audio, Video and Similar Electronic Apparatus – Safety Requirements音頻、視頻和類似電子設備.安全要求

EN 1329-1:2014+Amd.1:2018- Section 8 (PVC-U管及管件) Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems建筑結構內土壤和廢物排放(低溫和高溫)用塑料管道系統.未增塑聚氯乙烯(PVC-U).第1部分：管道、配件和系統規范

EN ISO 2507-1:2017 (取代EN 727-1994)(熱塑性管和配件) Thermoplastics pipes and fittings - Vicat softening temperature - Part 1: General test method熱塑性塑料管和配件維卡軟化溫度第1部分：通用試驗方法

BS 5577-1999(R2016) Section 7.7 (帶塑料柄的臺面餐具)Specification for Table Cutlery with Non-Metallic Handles非金屬把手餐具規范

吸水率Water absorption

ASTM D1003-13 Method A, Method B Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics透明塑料霧度和透光率的標準試驗方法

GB/T 2410-2008 Method A, Method B Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics透明塑料霧度和透光率的標準試驗方法

JIS K7361-1:1997 Plastics - Determination of the Total Luminous Transmittance of Transparent Materials - Part 1: Single Beam Instrument塑料.透明材料總透光率的測定.第1部分：?jiǎn)喂馐鴥x器

ISO 13468-1:2019 Plastics - Determination of the Total Luminous Transmittance of Transparent Materials - Part 1: Single Beam Instrument塑料.透明材料總透光率的測定.第1部分：?jiǎn)喂馐鴥x器

ANSI/SAE Z26.1-1996 第5.2節 (安全玻璃材料)Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways - Safety Standard在陸地公路上運行的機動車輛和機動車輛設備用安全玻璃材料.安全標準

霧度Haze

ASTM D1003-13 Method A, Method B Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics 透明塑料霧度和透光率的標準試驗方法

GB/T 2410-2008 Method A, Method B Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics 透明塑料霧度和透光率的標準試驗方法

ISO 14782:1999/Cor 1:2005 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics 透明塑料霧度和透光率的標準試驗方法

JIS K7136: 2000/Cor.1:2010 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics 透明塑料霧度和透光率的標準試驗方法

阻隔率Blocking rate

ASTM E903-12 Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres用積分球測定材料的太陽吸收率、反射率和透射率的標準試驗方法

光譜透射率Spectral transmittance

ASTM E903-12 第8.3.4節 Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres用積分球測定材料的太陽吸收率、反射率和透射率的標準試驗方法

光譜反射率Spectral reflectivity

ASTM E903-12 第8.3.4節 Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres用積分球測定材料的太陽吸收率、反射率和透射率的標準試驗方法

鏡面光澤度Specular gloss

ASTM D2457-13 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics塑料薄膜和固體塑料鏡面光澤的標準試驗方法

ASTM D523-14(2018) Standard Test Method for Specular Gloss 鏡面光澤的標準試驗方法

GB/T 8807-88 Standard Test Method for Specular Gloss 鏡面光澤的標準試驗方法

JIS Z8741:1997 Standard Test Method for Specular Gloss 鏡面光澤的標準試驗方法

鏡面反射率和鏡面光澤度Specular reflectance and specular gloss

ISO 7668:2018 Method A、Method C、Method D (陽極氧化膜)Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20°, 45°, 60° or 85°鋁及其合金的陽極氧化.在20°、45°、60°或85°角下陽極氧化涂層的鏡面反射和鏡面光澤的測量

GB/T 20503-2006方法A、方法C、方法D (陽極氧化膜) Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20°, 45°, 60° or 85°鋁及其合金的陽極氧化.在20°、45°、60°或85°角下陽極氧化涂層的鏡面反射和鏡面光澤的測量

顏色Color

ASTM D6290-13 (塑料粒子) Standard Test Method for Color Determination of Plastic Pellets塑料顆粒顏色測定的標準試驗方法

吸水率Water Absorption

ASTM D570-98(2018) Standard Test Method for Water Absorption of Plastics塑料吸水性的標準試驗方法

ASTM D229-19e1 Section 27 (電絕緣用的硬板材) Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation電絕緣用剛性薄板和板材的標準試驗方法

IDT ASTM D570-98(2018) Standard Test Method for Water Absorption of Plastics塑料吸水性的標準試驗方法

ASTM D349-13 Section 26-27 (電絕緣層壓棒) Standard Test Methods for Laminated Round Rods Used for Electrical Insulation電絕緣用層壓圓棒的標準試驗方法

ISO 62:2008 Plastics - Determination of water absorption塑料.吸水率的測定

GB/T 1034-2008 Plastics - Determination of water absorption塑料.吸水率的測定

JIS K7209:2000 Plastics - Determination of water absorption塑料.吸水率的測定

GB/T 23641-2018 Section 7.21 Fiber reinforced unsaturated polyester moulding compounds (SMC and BMC) for electrical purposes電氣用纖維增強不飽和聚酯模塑料(SMC/BMC)

ASTM D348-13 (電絕緣材料用硬管)Standard Test Methods for Rigid Tubes Used for Electrical Insulation電絕緣用剛性管的標準試驗方法

IDT ASTM D570 Standard Test Method for Water Absorption of Plastics塑料吸水性的標準試驗方法

耐化學試劑Chemical Resitance

ASTM D543-14 方法A (浸泡法) Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents評估塑料耐化學試劑性的標準實施規程

ISO 175:2010 (浸泡法) Plastics; determination of the effects of liquid chemicals, including water 塑料；液體化學品(包括水)影響的測定

GB/T 11547-200塑料；液體化學品(包括水)影響的測定8(浸泡法) Plastics; determination of the effects of liquid chemicals, including water 塑料；液體化學品(包括水)影響的測定

耐環境應力開裂Resistance to environmental stress cracking(ESC)

ASTM D1693-15 (乙烯塑料) Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics乙烯塑料環境應力開裂的標準試驗方法

GB/T 1842-2008 (聚乙烯) Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics乙烯塑料環境應力開裂的標準試驗方法

GB/T 2951.41-2008 (電線電纜等用料) Common test method for insulating and sheathing materials of electric and optical cables.Part 41:Methods specific to polyethylene and polypropylene compounds.Resistance to environmental stress cracking. 電纜和光纜絕緣和護套材料通用試驗方法 第41部分：聚乙烯和聚丙烯混合料專用試驗方法—耐環境應力開裂試驗

ISO 8442-1:1997 clause 6.6 (餐廚用刀具、容器) Materials and Articles in Contact with Foodstuffs - Cutlery and Table Holloware - Part 1: Requirements for Cutlery for the Preparation of Food與食品接觸的材料和物品.餐具和凹形餐具.第1部分：食品制備用餐具的要求

GB/T 15819-2006 (PE管) Polyethylene (PE) pipes for irrigation laterals - Test method and specification of susceptibility to environmental stress cracking induced by insert-type fittings灌溉用聚乙烯(PE)管材由插入式管件引起環境應力開裂敏感性的試驗方法和技術要求

BS 5577-1999(R2016) Section 7.8 (帶塑料柄的臺面餐具) Specification for Table Cutlery with Non-Metallic Handles非金屬把手餐具規范

球壓測試Ball pressure test

IEC 60695-10-2:2014 方法A Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method火災危險試驗第10-2部分：異常高溫球壓試驗方法

GB/T 5169.21-2017 方法A Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method火災危險試驗第10-2部分：異常高溫球壓試驗方法

IEC 60695-10-2:2014 方法B Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method火災危險試驗第10-2部分：異常高溫球壓試驗方法

GB/T 5169.21-2017 方法B Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method火災危險試驗第10-2部分：異常高溫球壓試驗方法

模具收縮率Shrinkage from mold dimension

ASTM D955-08(2014) Type A/ Type D2 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics測量熱塑性塑料模具尺寸收縮率的標準試驗方法

ISO 294-4:2018 Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 4: Determination of Moulding Shrinkage塑料.熱塑性材料試樣的注射成型.第4部分：成型收縮率的測定

GB/T 17037.4-2003 Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 4: Determination of Moulding Shrinkage塑料.熱塑性材料試樣的注射成型.第4部分：成型收縮率的測定

粘數Viscosity Number

ISO 307:2019 (聚酰胺) Plastics - Polyamides - Determination of viscosity number塑料.聚酰胺.粘度值的測定

GB/T 12006.1-2009 (聚酰胺) Plastics - Polyamides - Part 1: Determination of viscosity number塑料聚酰胺第1部分：黏數測定

ISO 1628-5:1998 (熱塑性聚酯) Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 5: Thermoplastic Polyester (TP) Homopolymers and Copolymers塑料.用毛細管粘度計測定稀釋溶液中聚合物的粘度.第5部分：熱塑性聚酯(TP)均聚物和共聚物

GB/T 1632.5-2008 (熱塑性聚酯) Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 5: Thermoplastic Polyester (TP) Homopolymers and Copolymers塑料.用毛細管粘度計測定稀釋溶液中聚合物的粘度.第5部分：熱塑性聚酯(TP)均聚物和共聚物

特性粘度Inherent Viscosity or Inherent Viscosity

ASTM D4603-18(PET) Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer用玻璃毛細管粘度計測定聚對苯二甲酸乙二醇酯(PET)特性粘度的標準試驗方法

GB/T 17931-2018 (瓶用聚對苯二甲酸乙二酯(PET)樹脂) Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer用玻璃毛細管粘度計測定聚對苯二甲酸乙二醇酯(PET)特性粘度的標準試驗方法

GB/T 29284-2012 (PLC) Poly聚乳酸

GB/T 14190-2017 (纖維級聚酯切片) Testing method of fiber grade polyester (PET) chip纖維級聚酯(PET)切片試驗方法

粘度viscosity

ISO 1628-2:2020 (PVC) Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 2: Poly(vinyl chloride) resins塑料.用毛細管粘度計測定稀釋溶液中聚合物的粘度.第2部分：聚氯乙烯樹脂

GB/T 3401-2007 (PVC) Determination of the viscosity of Poly(vinyl chloride)resins in dilute solution using capillary viscometers用毛細管黏度計測定聚氯乙烯樹脂稀溶液的黏度

ASTM D1243-95(2008) (PVC) Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers氯乙烯聚合物稀溶液粘度的標準試驗方法

HG/T 2234-91 (PC) Test method for viscosity of polycarbonate dilute solution聚碳酸脂稀溶液粘數的測定方法

ISO 1628-4:1999 (PC) Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 4: Polycarbonate (PC) Moulding and Extrusion Materials塑料.用毛細管粘度計測定稀釋溶液中聚合物的粘度.第4部分：聚碳酸酯(PC)模塑和擠出材料

粘接力測試Adhesion test

VDI 2019 Testing the adhesion of thermoplastic elastomers (TPE) on substrates測試熱塑性彈性體(TPE)在基材上的附著力

扭轉剛度Torsional Stiffness

ASTM D1043-16 Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test用扭轉試驗法測定塑料剛度特性隨溫度變化的標準試驗方法

GB/T 15047-1994 Test method for stiftness proporties in forsion of plastics塑料扭轉剛性試驗方法

ISO 458-1: 1985 Plastics - Determination of Stiffness in Torsion of Flexible Materials - Part 1: General Method塑料.柔性材料扭轉剛度的測定.第1部分：一般方法

TSM5601G-2009 第4.3.3節 材料規格

顆粒外觀(黑粒)Appearance of granules(Black granule)，顆粒外觀(大粒和小粒)Appearance of granules(large and small granule)

SH/T 1541.1-2019 塑料顆粒外觀試驗方法第1部分：目測法

水分含量Water Content

ISO 15512: 2019 Method B2 Plastics - Determination of water content塑料.水含量的測定

SH/T 1770-2010 方法A(聚乙烯) Plastic-Determintion of water content for polyethylene塑料聚合物 聚乙烯水分含量測定

ISO 15512: 2019 Method B1 Plastics - Determination of water content塑料.水含量的測定

SH/T 1770-2010 方法B(聚乙烯) Plastic-Determintion of water content for polyethylene塑料聚合物 聚乙烯水分含量測定

GB/T 22313-2008方法B 塑料用于聚氨酯生產的多元醇水含量的測定

ASTM D6869-17 Standard Test Method for Coulometric and Volumetric Determination of Moisture in Plastics Using the Karl Fischer Reaction (the Reaction of Iodine with Water)用卡爾費休反應(碘與水的反應)庫侖和體積法測定塑料中水分的標準試驗方法

揮發物含量Volatile Matter Content

ASTM D3030-17 (聚氯乙烯樹脂) Standard Test Method for Volatile Matter (Including Water) of Vinyl Chloride Resins氯乙烯樹脂揮發物(包括水)的標準試驗方法

GB/T 2914-2008 方法A(氯乙烯均聚和共聚樹脂)Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water)塑料.氯乙烯均聚物和共聚物樹脂.揮發性物質(包括水)的測定

ISO 1269:2006 Method A (氯乙烯均聚和共聚樹脂) Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water)塑料.氯乙烯均聚物和共聚物樹脂.揮發性物質(包括水)的測定

EN 12099:1997 (PE管材及管件)Plastics piping systems - Polyethylene piping materials and components - Determination of volatile matter content塑料管道系統.聚乙烯管道材料和部件.揮發性物質含量的測定

增塑劑加熱減量測試Mass Loss of Plasticizer on Heating

GB/T 1669-2001 Plasticizers-Determination of mass loss on heating增塑劑加熱減量的測定標準

尺寸穩定性Dimensional stability

ASTM D1710-15 Section 12.5(PTFE)Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes擠壓聚四氟乙烯(PTFE)桿、厚壁管和基本形狀的標準規范

高溫釋放HCl及酸性物質的測定—剛果紅測試法Determination of Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures

GB/T 2917.1-2002 Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to Evolve Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures - Part 1: Congo Red Method塑料.基于氯乙烯均聚物和共聚物的化合物和產品在高溫下釋放氯化氫和任何其他酸性產品的趨勢的測定.第1部分：剛果紅法

ISO 182-1:1990 Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to Evolve Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures - Part 1: Congo Red Method塑料.基于氯乙烯均聚物和共聚物的化合物和產品在高溫下釋放氯化氫和任何其他酸性產品的趨勢的測定.第1部分：剛果紅法

熱穩定性Heat stability

JIS K6723:1995+Amd.1:2006 Section 6.7(增塑的PVC) Plastic polyvinyl chloride compounds增塑聚氯乙烯化合物

熱處理質量損失Weight Loss on Heating

ASTM D706-15 (醋酸纖維素) Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)醋酸纖維素模塑和擠壓化合物(CA)規范的標準分類系統和基礎

磨痕寬度Scar width體積磨損Wear volume質量磨損Wear weight摩擦系數Friction coefficient

GB/T 3960-2016 Plastic-Test method for friction and wear by sliding塑料滑動摩擦磨損試驗方法

壓差法測試硫化橡膠或熱塑性橡膠透氣性的測定Rubber, vulcanized or thermoplastic-determination of permeability to gases:Differential-pressure methods

GB/T 7755.1-2018 Rubber, vulcanized or thermoplastic - Determination of permeability to gases - Part 1: Differential-pressure methods硫化橡膠或熱塑性橡膠透氣性的測定第1部分：壓差法

ISO 2782-1:2016 Rubber, vulcanized or thermoplastic - Determination of permeability to gases - Part 1: Differential-pressure methods硫化橡膠或熱塑性橡膠透氣性的測定第1部分：壓差法

氣體透過率-庫侖計法Gas Transmission Rate-Coulometric Sensor

ISO 15105-2:2003 Plastics Film and sheeting Determination of gas-transmission rate Part 2: Equal-pressure method塑料薄膜和薄板氣體傳輸速率的測定第2部分：等壓法

GB/T 19789-2005 Packaging material.Test method for oxygen gas permeability characteristics of plastic film and sheeting.Coulometric sensor包裝材料塑料薄膜和薄片氧氣透過性試驗庫侖計檢測法

GB/T 31354-2014 Determination of oxygen gas transmission rate through dry packages.Coulometric sensor包裝件和容器氧氣透過性測試方法庫侖計檢測法

YBB 00082003-2015 氣體透過量測定法

ASTM F1307-2020 Standard Test Method for Oxygen Transmission Rate Through Dry Packages Using a Coulometric Sensor用庫侖傳感器測定干燥包裝中氧氣透過率的標準試驗方法

ASTM D3985-2017 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor用庫侖傳感器測定通過塑料薄膜和薄板的氧氣傳輸率的標準試驗方法